Abstract:
An optocoupler circuit includes first and second resistors, an optocoupler, a reference circuit, and a comparator. The optocoupler includes a light source and a phototransistor. The light source is connected to form a first voltage divider with the first resistor. The phototransistor is connected to form a second voltage divider with the second resistor. The optocoupler transitions an output of the second voltage divider between first and second levels. Magnitudes of the first and second levels are greater than zero. The reference circuit is configured to output a reference voltage. The comparator includes a first input and a second input. The first input receives an output of the first voltage divider. The second input receives the reference voltage. An output of the comparator transitions between a third level and a fourth level based on a comparison between the output of the first voltage divider and the reference voltage.
Abstract:
A desired OFF period module is configured to determine a desired OFF period for a plurality of switches of a PFC circuit based on an input voltage and an output voltage. A blanking timer module is configured to output a blanking signal, set the blanking signal to a first state when a countdown timer is greater than zero, and set the blanking signal to a second state when the countdown timer reaches zero. A switching control module is configured to: transition a first switch of the plurality of switches from an ON state to an OFF state in response to (i) a measured current through an inductor of the PFC circuit being greater than a demanded current through the inductor and (ii) the blanking signal being in the second state; and maintain the first switch in the OFF state for the desired OFF period after the transition.
Abstract:
A system includes a compressor having a shell housing a compression mechanism driven by an electric motor in an on state and not driven by the electric motor in an off state. The system also includes a variable frequency drive that drives the electric motor in the on state by varying a frequency of a voltage delivered to the electric motor and that supplies electric current to a stator of the electric motor in the off state to heat the compressor.
Abstract:
A current control module generates a voltage request based on a d-axis current (Idr) demand. A switching control module controls a motor based on the voltage request and generates an out-of-volts (OOV) signal based on a comparison of the voltage request and an available voltage. An Idr injection module generates the Idr demand based on a direct current (DC) bus voltage, a rotational speed, and a demanded torque and selectively applies a first adjustment to the Idr demand. The Idr injection module identifies whether an improvement resulted from the first adjustment, wherein the improvement is identified based on at least one of (i) a measured current of the motor and (ii) the OOV signal. The Idr injection module selectively applies a second adjustment to the Idr demand based on whether the improvement is identified.
Abstract:
A system includes a pulse-width modulation (PWM) module, a subtraction module, an error reducing module, and a summing module. The PWM module controls switching of an inverter that powers a motor. The PWM module controls the switching based on a first angle in a first mode and a second angle in a second mode. The subtraction module determines a difference between the first and second angles. The error reducing module (i) stores the difference when a transition from the first mode to the second mode is commanded and (ii) decreases a magnitude of the stored difference to zero. The summing module calculates a sum of the stored difference and the second angle. The PWM module controls the switching based on the sum in the second mode.
Abstract:
A power factor correction (PFC) system includes a period determination module, a frequency generation module, an angle generation module, a signal generation module, and an angle correction module. The period determination module determines a period of an input alternating current (AC) line signal based on a time between rising edges of the input AC line signal. The frequency generation module generates a frequency based on the period. The angle generation module generates an angle based on the frequency. The signal generation module generates a sinusoidal reference signal based on the frequency and an adjusted angle. The angle correction module generates the adjusted angle based on the angle and based on a comparison of a falling edge of the sinusoidal reference signal, the period, and a rising edge of the input AC line signal.
Abstract:
A system for controlling a capacity of a compressor includes a motor of the compressor including a main winding connected at a connection point to an auxiliary winding and a drive configured to control a speed of the motor. The system includes a first switch configured to selectively connect the main winding to either a first line voltage or a first output of the drive, a second switch configured to selectively connect the connection point to either a second line voltage or a second output of the drive, and a third switch configured to selectively connect the auxiliary winding to either a capacitor or a third output of the drive. The system includes a solenoid valve configured to selectively either operate in a first capacity or a second capacity. The system includes a control module configured to control the drive, the first switch, the second switch, and the third switch.
Abstract:
A control system for a motor includes a pulse-width modulation module, a pulse skip determination module, and a duty cycle adjustment module. The pulse-width modulation module generates three duty cycle values based on three voltage requests, respectively. A plurality of solid-state switches control three phases of the motor in response to the three duty cycle values, respectively. The pulse skip determination module generates a pulse skip signal. The duty cycle adjustment module selectively prevents the plurality of solid-state switches from switching during intervals specified by the pulse skip signal.
Abstract:
A power factor correction (PFC) system includes a comparison module, an adjustment module, a compensation module, and a duty cycle control module. The comparison module measures N currents having different phases, and generates (N-1) comparisons based on the N measured currents, wherein N is an integer greater than one. The adjustment module determines (N-1) time advance adjustments based on the (N-1) comparisons, respectively. The compensation module generates N compensated versions of an input alternating current (AC) line signal based on the input AC line signal, a sinusoidal reference signal, and the (N-1) time advance adjustments, wherein the sinusoidal reference signal is synchronized to the input AC line signal in phase and frequency. The duty cycle control module controls PFC switching based on the N compensated versions of the input AC line signal.
Abstract:
A power factor correction (PFC) system comprising a PFC circuit that receives an alternating current (AC) input voltage and that, using a switch, generates a direct current (DC) output voltage from the AC input voltage; a first zero crossing module that determines a first zero crossing of the AC input voltage based on: a first voltage and a first time when the AC input voltage transitioned from less than a first predetermined voltage to greater than the first predetermined voltage; and a second voltage and a second time when the AC input voltage transitioned from less than a second predetermined voltage to greater than the second predetermined voltage, wherein the first predetermined voltage is less than zero, and wherein the second predetermined voltage is greater than zero; a reference module that, based on the first zero crossing, generates a sinusoidal reference signal that corresponds to the AC input voltage at least in phase and frequency; and a switching control module that controls switching of the switch based on the sinusoidal reference signal.