Abstract:
Electric aircraft, including in-flight rechargeable electric aircraft, and methods of operating electric aircraft, including methods for recharging electric aircraft in-flight, through the use of unmanned aerial vehicle (UAV) packs flying independent of and in proximity to the electric aircraft.
Abstract:
The mode of landing of an unmanned aerial vehicle driven by an electric engine, containing main power supply batteries, control systems of the surveillance head, transmitting and receiving systems, a flight control system, and a container equipped with a surveillance head with a looking down lens, placed in a recess situated in the lower part of the fuselage by which the vehicle is lightened at the last stage of flight shortly before landing, which means the container placed in the recess is detached, then moved outside the vehicle's body and descended by means of a parachute into a desired location, and the lightened vehicle lands in some other place. The recess in the fuselage contains an electrically controlled lock which fixes detachably the container equipped with at least one parachute placed at the bottom section of the container, on the side of the surveillance head.
Abstract:
An aircraft for unmanned aviation is described. The aircraft includes an airframe, a pair of fins attached to a rear portion of the airframe, a pair of dihedral braces attached to a bottom portion of the airframe, a first thrust-vectoring (“T/V”) module and a second T/V module, and an electronics module. The electronics module provides commands to the two T/V modules. The two T/V modules are configured to provide lateral and longitudinal control to the aircraft by directly controlling a thrust vector for each of the pitch, the roll, and the yaw of the aircraft. The use of directly articulated electrical motors as T/V modules enables the aircraft to execute tight-radius turns over a wide range of airspeeds.
Abstract:
A method of launching a powered unmanned aerial vehicle at an altitude of at least 13,000 m, the method comprising lifting the vehicle by attachment to a lighter-than-air carrier from a substantially ground-level location to an elevated altitude, causing the vehicle to detach from the carrier while the velocity of the vehicle relative to the carrier is substantially zero, the vehicle thereafter decreasing in altitude as it accelerates to a velocity where it is capable of preventing any further descent and can begin independent sustained flight.
Abstract:
A control system that makes adjustments, such as limiting the maximum speed or maximum torque in a vehicle, is provided. These adjustments can be based on knowledge about the vehicle and trip, and on the estimated energy remaining. The control system is applicable to a wide range of vehicles, including ground, air, water, and sea vehicles, as well as vehicles powered by battery, electricity, compressed natural gas, or even liquid fuel propulsion systems. The control system may be used to adjust vehicle operation in route to assure the vehicle reaches a destination and to inform or counteract a human vehicle operator. Control system can also be used in racing applications to calculate the fastest-possible race speed and drive torque for a given race length; or alternatively, in endurance racing or delivery applications to optimize the vehicle speed and/or drive torque for a given race length or route.
Abstract:
Disclosed is an aircraft, configured to have a wide range of flight speeds, consuming low levels of power for an extended period of time, while supporting a communications platform with an unobstructed downward-looking view. The aircraft includes an extendable slat at the leading edge of the wing, and a reflexed trailing edge. The aircraft comprises a flying wing extending laterally between two ends and a center point. The wing is swept and has a relatively constant chord. The aircraft also includes a power module configured to provide power via a fuel cell. The fuel cell stores liquid hydrogen as fuel, but uses gaseous hydrogen in the fuel cell. A fuel tank heater is used to control the boil-rate of the fuel in the fuel tank. The fuel cell compresses ambient air for an oxidizer, and operates with the fuel and oxidizer at pressures below one atmosphere.
Abstract:
A method for transferring airplanes and an unmanned airplane transfer system. The airplane transferring system includes: receiving a transfer signal responsive of a movement of an airplane control component; and transferring an airplane, by an unmanned airplane transfer system, in response to the transfer signal.
Abstract:
A hollow elliptical-cylindrical hull conformingly houses a hollow rectangular-prismatic cabin whereby the four longitudinal parallel outside edges of the latter make contact with the inside surface of the former. The fully constructed aircraft (either non-powered or powered) includes the integral hull-plus-cabin structure along with nose, tail and airfoil structures that are coupled therewith. The cabin conformingly accommodates hollow rectangular-prismatic modules useful for cargo storage. While the nose and/or tail structure is uncoupled from the integral hull-plus-cabin structure, the modules are inserted into the cabin and the cabin is sealed. The aircraft is lifted (e.g., via airplane, helicopter, rocket or balloon) to a particular elevation and released, whereupon the two wings fully emerge and the aircraft effects controlled flight until reaching its destination. After landing, the nose and/or tail structure is uncoupled from the integral hull-plus-cabin structure, the cabin is unsealed, and the modules are removed from the cabin.
Abstract:
A small radio controlled flying device propelled by a thermal engine (20) with pusher type airscrew (19) for remote sensing, the device being capable of short take-off and landing and flying at maximum speed of 35 Km/h. The device includes a pod and wings, the pod (1) being a rigid tricycle carriage dismountable by disengagement of substantially pyramidal jig with rear base (2) and front apex (7), lower plane (3), two lateral planes (4, 5) and an upper plane (6). The base is a welded one-piece element that includes the engine, the airscrew, a tank and the radio control. The apex is a welded one-piece element. The lower plane and the two lateral planes include spars (11, 12) assembled at the base and as the apex. The lower plane includes at its three end angles two rear wheels (8) and a front wheel (9), the front wheel being provided to protrude towards the front in the apex and the wheels being low pressure tires. The wings (13) are a caisson-type supple parachute and are connected to the pod in an adjustable fashion by two front slings (17), two braking slings (18) acting on the two flaps/ailerons.
Abstract:
An anti-submarine warfare system includes an unmanned “sea-sitting” aircraft housing submarine detecting equipment, the aircraft including a body portion having a catamaran configuration adapted for stably supporting the body portion when sitting in water, the body portion including a fuselage and laterally disposed sponsons connected to the fuselage via platforms, and submarine detecting equipment housed within the fuselage and adapted to be electronically linked to sonobuoys disposed in adjacent water locations.